مقاله کنفرانسی سال ۱۴۰۲ انگلیسی

FEM simulation of extracting pull-out force for insert sandwich panels

FEM simulation of extracting pull-out force for insert sandwich panels

چکیده مقاله

Sandwich panel inserts are susceptible to pull out loads, and predicting the pull out force is challenging due to the many damage mechanisms that may occur To investigate the simulation of extracting the pull out force, for the inserts of sandwich panels, a research by Mr Ralph Seaman and Dieter Krause 1 , under the title of numerical modeling of partially potted inserts in honeycomb sandwich panels under pull out load, has been investigated In this article, the analysis for two nonlinear finite element states is described One of these two models is a continuous 3D model in which the core honeycomb sandwich panel is analyzed using 8 nodes with a homogeneous material model, and the other is a detailed mesoscale model with a detailed honeycomb cell representation, which is The use of 4 nodes is modeled The simulation results are compared with the experimental data of the reference configuration Both models are capable of accurately predicting power, while the continuous 3D model can be considered favorable for most applications due to the reduced computational effort Next, the three dimensional model of the meso scale was analyzed in Abaqus software and the results obtained were compared with the results of the mentioned article

کلیدواژه‌ها

نویسندگان

تصویر Moein Chobkar

Moein Chobkar

Master's student in manufacturing mechanical engineering, University of Tehran

تصویر Abolfazl Torabiyan

Abolfazl Torabiyan

Master's student in manufacturing mechanical engineering, Noshirvani University of Technology, Babol

تصویر Hosein Zakeri

Hosein Zakeri

Master's student in manufacturing mechanical engineering, Noshirvani University of Technology, Babol

شیوه ارجاع

Chobkar, Moein and Torabiyan, Abolfazl and Bafti Zahirabadi, Ahmadreza and Zakeri, Hosein,1402,FEM simulation of extracting pull-out force for insert sandwich panels,The 9th International and 20th National Conference on Manufacturing Engineering,Tehran

ارائه‌شده در

پوستر مجموعه مقالات بیستمین همایش ملی و نهمین کنفرانس بین المللی مهندسی ساخت و تولید ایران مجموعه مقالات بیستمین همایش ملی و نهمین کنفرانس بین المللی مهندسی ساخت و تولید ایران2 اسفند 1402 · تهران
ادامه مسیر پژوهش

مقالات مرتبط

مقاله کنفرانسی سال ۱۴۰۱ ۲,۶۲۷ مشاهده

بررسی تجربی اثر الکتروپلاستیک بر رفتار کرنش ورق آلومینیومی ۶-T۶۰۶۱ از طریق آزمایش کشش

نتایج پژوهش های صورت گرفته از سوی محققان نشان داده است که اعمال جریان الکتریکی به فلز در حین تغییرشکل می…

الکتروپلاستیک آزمایش کشش آلومینیوم۶۰۶۱شکل دهی به کمک الکتریسیته
مقاله کنفرانسی سال ۱۴۰۱ ۱,۳۷۲ مشاهده

انتخاب فولاد مناسب برای سازه های دریایی

انتخاب ماده در طراحی و ساخت سازه های مهندسی یکی از موضوعات مهم در مهندسی ساخت و تولید می باشد عموما سازه…

سازه های دریاییآلیاژهای فولادانتخاب ماده
مقاله کنفرانسی سال ۱۴۰۱ ۱,۲۱۶ مشاهده

اثر ارتعاش التراسونیک بر کیفیت سوراخ در عملیات سوراخکاری فولاد سخت شده ۱.۷۲۲۵

فرایند سوراخکاری به عنوان روش متداول جهت براده برداری مواد، دارای معایبی از جمله کیفیت پایین سطوح در قطع…

التراسونیک ارتعاش سوراخکاری ماشینکاری
مقاله کنفرانسی سال ۱۴۰۱ ۷۶۷ مشاهده

مقایسه شرایط فرایند و عیوب تزریق پلاستیک در جایگزینی پلیمر زیست تخریب پذیر پلی لاکتیک اسید (PLA) باپلی پروپیلن (PP) برای تولید لوله های سانتریفیوژ (فالکون)

پلی لاکتیک اسید پلیمری زیست تخر یب پذیر است که خواص فیزیکی وفرآیندپذ یری قابل مقایسه با پلیمرهای معمول ر…

تزریق پلاستیک پلی لاکتیک اسید نرم افزار Moldflow
مقاله کنفرانسی سال ۱۴۰۱ ۷۲۲ مشاهده

شناسایی و بررسی انواع روشهای ساخت و تولید توربین های محوری در توربین گازی

امروزه به دلیل رشد اقتصادی و افزایش جمعیت، تقاضا برای انرژی در سطح جهانی افزایش یافته است توربینها به من…

توربین گازیسوپرآلیاژ پایه نیکلCNC پنج محور
مقاله کنفرانسی سال ۱۴۰۱ ۶۷۶ مشاهده

استفاده از فناوری کنترل عددی در رسم و نقاشی دو بعدی با استفاده از نازل رنگ پاش

امروزه فناوری کنترل عددی Numerical Control که از فرزکاری دو محوره بال هواپیما در دانشگاه MIT در سال ۱۹۶۸…

کنترل عددی پروفیل حرکت تبدیل مختصات بورد آردوینو GRBL نازل رنگ پاش