مقاله کنفرانسی سال ۱۴۰۳ انگلیسی

Thermo-Mechanical Processing-Induced Microstructure Refinement of Co-28Cr-6Mo-0.33C Alloy and Its Impact on Wear Behavior

Thermo-Mechanical Processing-Induced Microstructure Refinement of Co-28Cr-6Mo-0.33C Alloy and Its Impact on Wear Behavior

چکیده مقاله

Grain refinement in Co 28Cr 6Mo 0 33C alloy was achieved through minimal plastic deformation and a two step heat treatment The solution treated specimens were furnace cooled, resulting in a pearlitic structure at grain boundaries These were then compressed and aged at 850°C, leading to the decomposition of the austenite phase into a lamellar eutectoid structure α M23C6 Reverse treatment at temperatures stabilizing austenite facilitated nucleation of a fine grained austenitic structure with an average grain size of 48 23 μm, about one tenth of the original size The hot compression behavior was examined between 1100 1200°C and strain rates of 0 001 1 s 1 The activation energy was calculated as 744 6 kJ/mol Microstructural analysis showed competition between dynamic recrystallization DRX and precipitation, especially at low strain rates 0 001 s 1 Precipitates at grain boundaries hindered DRX, while prolonged coarsening of precipitates promoted DRX This competition caused serrated grain boundaries and oscillations in the flow curves Wear behavior, assessed by pin on disk tests, indicated that carbide shape, distribution, and size significantly affected wear resistance Large and lamellar carbides resulted in lower wear resistance compared to fine globular carbides in solution treated and quenched specimens ε Martensite formation during sliding reduced wear rate due to fewer slip systems in the hexagonal structure

کلیدواژه‌ها

نویسندگان

تصویر Aydin Doroudi

Aydin Doroudi

PhD Candidate, Polymer and Color Engineering Department, Amirkabir University of Technology

شیوه ارجاع

Hassani Jabali, Fatemeh Zahra and Doroudi, Aydin,1403,Thermo-Mechanical Processing-Induced Microstructure Refinement of Co-28Cr-6Mo-0.33C Alloy and Its Impact on Wear Behavior,The10th International and 21th National Conference on Manufacturing Engineering,Tehran

ارائه‌شده در

پوستر مجموعه مقالات بیست و یکمین همایش ملی و دهمین کنفرانس بین المللی مهندسی ساخت و تولید ایران مجموعه مقالات بیست و یکمین همایش ملی و دهمین کنفرانس بین المللی مهندسی ساخت و تولید ایران6 اسفند 1403 · تهران
ادامه مسیر پژوهش

مقالات مرتبط

مقاله کنفرانسی سال ۱۴۰۲ ۵۰۸ مشاهده

بررسی تجربی و ارائه مدل نئو-هوکین Neo-Hookean برای تیر ساخته شده با چاپگر سه بعدی ازجنس TPU

با توجه به کاربرد روز افزون مواد هایپرالاستیک در صنایع مختلف بررسیومدلسازی آنها برای پیش بینی رفتارشان ا…

مواد هایپرالاستیکساخت افرایشیآزمون کشش
مقاله کنفرانسی سال ۱۴۰۲ ۴۵۲ مشاهده

استخراج پروفیل هندسی واشرهای لاستیکی با استفاده از سیستم مثلثی لیزر خطی

از جمله مسائل مهم در کارکرد صحیح مبدل های حرارتی صفحه ایتمام واشر، آب بندی درست کانال های عبور سیال توسط…

پردازش تصویراستخراج پروفیل هندسیفیلترهای نوری
مقاله کنفرانسی سال ۱۴۰۲ ۴۳۵ مشاهده

استفاده از پراش پرتو ایکس جهت ارزیابی تغییرات تنش پسماند ناشی از اعمال فرایند نورد مستقیم ومعکوس به ورق آلومینیوم ۱۰۲۰ CGP شده

از آنجا که در فرایند CGP ورق های فلزی، به دلیل اثر گوشه های تیز قالبشیاردار، در سطح ورق ترک های ریز و تن…

تنش پسماندنوردآلومینیوم ۱۰۲۰
مقاله کنفرانسی سال ۱۴۰۲ ۴۳۱ مشاهده

طراحی و ساخت کامپوزیت تقویت شده با الیاف کربن برای دستیابی به خواص مکانیکی مورد نظر دراتصالات چسبی

در سالهای اخیر با توجه به امکان دستیابی به خصوصیات مختلف مکانیکیاز جمله مقاومت به سایش بالا، مقاومت به ح…

استحکامکامپوزیتالیاف
مقاله کنفرانسی سال ۱۴۰۲ ۴۳۰ مشاهده

بررسی و مقایسه فرآیند آهنگری(فشار مستقیم در حالت کرنش صفحه ای)به روش آنالیز اسلب و شبیه سازی در آباکوس

شکل دادن فلزات یا فرم دهی فلزات دانشی است که توسط آن یک ماده بهشکل مفیدی با خواص و ساختاری که برای محیط…

المان محدودنرم افزار آباکوسروش آنالیز اسلب تختا
مقاله کنفرانسی سال ۱۴۰۲ ۴۳۰ مشاهده

بهینه سازی شکست ساختار لانه زنبوری با استفاده ازشبکه عصبی مصنوعی و الگوریتم ژنتیک

در جهان امروزی رقابت بسیاری میان مهندسان برای انتخاب ساختار بهینهبا استحکام و مقاومت بالا، سبکی بیشتر و…

جذب انرژیبهینه سازیالگوریتم ژنتیک