مقاله کنفرانسی سال ۱۳۹۹ انگلیسی

Effect of tool rotation speed in friction stir spot welding on microstructure, mechanical properties and thermal conductivity of pure copper and ST14 carbon steel joint

Effect of tool rotation speed in friction stir spot welding on microstructure, mechanical properties and thermal conductivity of pure copper and ST14 carbon steel joint

چکیده مقاله

In the present study, pure copper and plain carbon steel ST14 were bonded by point friction welding method The welding operation was performed by a tungsten carbide pinand three rotational speeds of 1000, 1250 and 1500 rpm and a time of 60 seconds were selected for the tool After welding, microhardness, tensile, thermal conductivity andmicrostructure tests were performed using light microscope and scanning electron microscope The microhardness test showed that the samples with higher rotational speed, the hardness of the welding button area was higher The results of tensile test showed that with increasing the rotational speed of the pin, the tensile strength of the specimens increased The results of thermal conductivity test showed that with increasing the rotational speed of the pin, the coefficient of thermal conductivity decreased The microstructural analysis of the samples showed that the connected samples with higher rotational speed, due to the increase of the inlet heat, and consequently the increase of the cooling rate, the recrystallization of the grains was faster and therefore smaller grains were formed

کلیدواژه‌ها

Solid State Welding Rotation Speed Friction Stir Spot Welding

نویسندگان

تصویر Farhad abdi

Farhad abdi

Phd Student of Metallurgy Engineering, Materials and Energy Research Center, Karaj, Iran

تصویر Hamed Sabet

Hamed Sabet

Associate Professor, Department of Materials Engineering, Karaj Islamic Azad University, Karaj, Iran

تصویر mosayeb Aghajani

mosayeb Aghajani

M Sc of Materials Engineering, Islamic Azad University, Karaj, Iran

شیوه ارجاع

abdi, Farhad and sabet, hamed and Aghajani, mosayeb,1399,Effect of tool rotation speed in friction stir spot welding on microstructure, mechanical properties and thermal conductivity of pure copper and ST14 carbon steel joint,3rd International Conference on Welding and Non-Destructive Testing of Iran, 21st National Conference on Welding and Inspection and 10th National Conference on Non-Destructive Testing,Isfahan

ارائه‌شده در

پوستر مجموعه مقالات سومین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب ایران، بیست و یکمین کنفرانس ملی جوش و بازرسی و دهمین کنفرانس ملی آزمایش های غیرمخرب مجموعه مقالات سومین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب ایران، بیست و یکمین کنفرانس ملی جوش و بازرسی و دهمین کنفرانس ملی آزمایش های غیرمخرب13 اسفند 1399 · اصفهان
ادامه مسیر پژوهش

مقالات مرتبط

مقاله کنفرانسی سال ۱۳۹۹ ۱,۴۳۴ مشاهده

کاربرد روش طراحی آزمایش تاگوچی در جوشکاری

روش تاگوچی توسط محققی به نام جنيچی تاگوچی جهت بهینه سازی فرآیند ها توسعه داده شد روش معمول انجام آزمایشه…

جوشکاریطراحی آزمایش تاگوچی.طراحی آزمایش تاگوچی
مقاله کنفرانسی سال ۱۳۹۹ ۱,۱۷۸ مشاهده

اتصال غیرمشابه آلیاژ تیتانیوم Ti6Al4V به آلیاژ آلومینیوم Al6061 به روش فاز مایع گذرا

آلیاژهای تیتانیم و آلومینیم به علت خواص جذابی مانند چگالی پایین، مقاومت خوردگی خوب و استحکام مناسب کاربر…

تیتانیمTi6Al4VAl6061
مقاله کنفرانسی سال ۱۳۹۹ ۹۹۵ مشاهده

ارزیابی تنش زدایی آلتراسونیک در جوشکاری GTAW و خوردگی تحت تنش (SCC) در فولاد زنگ نزن L 316 و مقایسه آن با روش حرارتی

جوشکاری به روش قوس تنگستنی GTAW از فرایند های پرکاربرد جوشکاری محسوب میشود که فلز جوش ممکن است با خوردگی…

خوردگی تنشیتنش زدایی آلتراسونیکتنش زدایی حرارتی
مقاله کنفرانسی سال ۱۳۹۹ ۹۸۵ مشاهده

مطالعه EBSD و شبیه سازی تنش های پسماند در اتصال غیرمشابه فاز مایع گذار فولاد زنگ نزن دوفازی 220 SAF به سوپر آلیاژ اینکونل 750-X

در این پژوهش، اتصال غير مشابه فولاد زنگ نزن دوفازی 2205 SAF به سوپر آلیاژ اینکونل 750 X توسط فرآیند فاز…

اینکونل 750-Xاستحکام کششی برشیفاز مایع گذرا
مقاله کنفرانسی سال ۱۳۹۹ ۹۶۷ مشاهده

بررسی افزایش استحکام الکترود, با رویکرد کاهش عملیات درسینگ در تغییرعناصرآلیاژی الکترود مورد استفاده در تولید بدنه خودروی پارس تندر

جوشکاری مقاومتی نقطه ای از مهمترین روش های جوشکاری بدنه خودروها می باشد در بدنه خودروها ورق های فولادی گ…

بدنه خودروفرآیند درسکاری الکترودسره موثر الکترود
مقاله کنفرانسی سال ۱۳۹۹ ۹۵۱ مشاهده

بررسی ریز ساختار نمونه فولاد زنگ نزن 316 کم کربن ساخته شده به روش رسوب مستقیم فلز

هدف از این پژوهش مشخصه یابی ریزساختار، عیوب و سختی نمونه فولاد زنگ نزن 316 کم کربن است که از روش رسوب مس…

ریزساختارروش رسوب مستقیم فلزفولاد زنگ نزن 316