مقاله کنفرانسی سال ۱۴۰۰ انگلیسی

Double wall Double Image Technique for very small pipes to assess the location of defects and Sensitivity in the butt weld of the tube

Double wall Double Image Technique for very small pipes to assess the location of defects and Sensitivity in the butt weld of the tube

چکیده مقاله

In this study, hydraulic pipes under 0 5 inches 0 5 and 0 75 inches with 1 0308 material were inspected and radiographically tested in the steelmaking unit after penetration welding and GTAW welding method Radiographic examination X ray imaging is one of the approved methods among non destructive tests to detect internal defects without damaging the tubes Small cracks and small defects, when the pipes are under pressure or pressure and exposed to a lot of heat, cause serious damage and cause many life and financial accidents In many cases, the quality of the radiographs is low due to the scattering of X rays and gamma rays In order to investigate the defects in lip to tube welding with maximum OD size 0 5 and 0 75 inches , the radiographic test was takenusing the double walled image DWDI technique with the least two exposures at right angles ASTM Hole or ASTM / Din is usually used and maintained to determine the radiographs, and here the size limitation prevented the image quality from being controlled In many cases, the quality of the radiographs was low due to the scattering of X rays and gamma rays Depending on the thickness of the tube and its OD, the radiographic source is placed on the weld with a slope of 12 to 15 degrees to obtain an elliptical image of the weld edge of the tube The welded tube is rotated at different angles by inserting the signals given by the DWDI technique and radiographed with source to film distance defect distance to different films The defect pattern at different angles of rotation and SFD has been predicted for the study

کلیدواژه‌ها

welding DWDI Radiographic test non-destructive testing tube . non destructive testing tube

نویسندگان

تصویر Sepehr Soleimani

Sepehr Soleimani

PhD in Metallurgical Materials Engineering, Department of Materials and Metallurgical Engineering,

تصویر Iman Hajiannia

Iman Hajiannia

Technical and Vocational University, Tehran, Iran and Mobarakeh Steel Engineering Company

شیوه ارجاع

Soleimani, Arash and Soleimani, Sepehr and Hajiannia, Iman,1400,Double wall Double Image Technique for very small pipes to assess the location of defects and Sensitivity in the butt weld of the tube,4th International Conference on Welding and Non Destructive Testing & 22nd National Conference on Welding & Inspection & 11th National Conference on NDT,Isfahan

ارائه‌شده در

پوستر مجموعه مقالات چهارمین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب و بیست و دومین کنفرانس ملی جوش و بازرسی و یازدهمین کنفرانس ملی آزمایش های غیرمخرب مجموعه مقالات چهارمین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب و بیست و دومین کنفرانس ملی جوش و بازرسی و یازدهمین کنفرانس ملی آزمایش های غیرمخرب18 اسفند 1400 · اصفهان
ادامه مسیر پژوهش

مقالات مرتبط

مقاله کنفرانسی سال ۱۴۰۰ ۱,۲۸۱ مشاهده

ارزیابی ریسک فرایند جوشکاری و برشکاری با رویکرد FMEA فازی

بدون تردید مدیریت ریسک، مهم ترین ماموریت نظام مدیریت ایمنی در صنایع می باشد ریسک همواره با عدم قطعیت همر…

ارزیابی ریسکفازیجوشکاری
مقاله کنفرانسی سال ۱۴۰۰ ۱,۰۳۶ مشاهده

آزمون های غیر مخرب در صنعت خودروسازی

نظر به اهمیت بالای کیفیت و صحت عملکرد قطعات و اجزاء خودرو در حصول اطمینان از کارایی و ایمنی خودروی تولید…

خودروUTMT
مقاله کنفرانسی سال ۱۴۰۰ ۹۵۵ مشاهده

تکنیک دودیواره دو تصویر برای لوله های با سایز بسیار کم برای ارزیابی مکان عیوب و حساسیت در جوش لب به لب لوله

در این تحقیق لوله های زیر اینچ هیدرولیک ۰/۵ و ۰/۷۵ اینچ با جنس ۱/۰۳۰۸ را در واحد فولادسازی پس از جوشکاری…

لولهآزمون پرتونگاریجوش
مقاله کنفرانسی سال ۱۴۰۰ ۸۰۳ مشاهده

انحلال ذرات کاربید تنگستن (WC) حین ایجاد لایه سخت جوشکاری و تاثیر آن بر مقاومت سایشی لایه کامپوزیتی WC/Ni

در پژوهش حاضر تاثیر انحلال ذرات کاربید تنگستن WC ناشی از شرایط مختلف پیش گرم نمودن قطعات قبل از جوشکاری…

ذرات پودری WCانحلال ذرات کاربید تنگستنتشکیل فاز ترد C۲W
مقاله کنفرانسی سال ۱۴۰۰ ۷۹۳ مشاهده

جوشکاری نقطه ای مقاومتی فولادهای پیشرفته در خودرو سازی

امروزه فراین د جوشکاری مقاومتی نقطه ای یکی از مهم ترین مراحل ساخت خودروها بشمار می رود افزایش ایمنی و سب…

ایمنیسبکیسوخت
مقاله کنفرانسی سال ۱۴۰۰ ۷۶۶ مشاهده

بررسی اثر زمان و دمای پیشگرم روی خواص مکانیکی منطقه متاثر از حرارت جوشکاری به روش GMAW/GTAW ، اتصال آلیاژ ۱.۷۲۲۵ (M۰۴۰) به St۳۷

اتصال فلزات غیرهمجنس یکی از مهم ترین الزامات صنایع مختلف است اتصال فولادهای آلیاژی و ساده کربنی به طور م…

مدت زمان پیشگرمدما پیشگرماتصال فلزات غیر همجنس