مقاله کنفرانسی سال ۱۴۰۰ انگلیسی

On the Microstructural and Hardness Variations of the Heat Affected Zone in the AA6082-T651 Weld Joints

On the Microstructural and Hardness Variations of the Heat Affected Zone in the AA6082-T651 Weld Joints

چکیده مقاله

In this paper, the variations of microstructure and hardness of the AA6082 T651 welding Heat Affected Zone HAZ has been studied To reach the aim, scanning and transmission electron microscopes equipped with EDS were used and hardness and micro hardness tests were performed The hardness of the base metal was 112 HV, which is suitable for 6082 aluminum alloy in the age hardened condition Evaluation of hardness variations based on distance from fusion line showed that Hardness decreased throughout wide HAZ However, the hardness of partially melted zone was higher than that of other heat affected zones due to fully dissolution of Mg2Si precipitates and the consequent natural aging In all specimens, there was a valley in HAZ hardness profiles with a value of about 55 HV half the base metal hardness Microstructural investigations of this zone revealed that βʺ precipitates were transformed into β and as aresult, the zone was over aged Moreover, the dislocation recovery caused to reduce dislocation density Therefore, over aging and dislocation recovery was determined as HAZ softening agents α Al15 Fe,Mn 3Si2 precipitates with blocky and Chinese script morphology were observed in the base metal microstructure In the PMZ, these precipitates mainly had blocky morphology with preferential placement on elongated rolled grain boundaries Sub micron Mn rich spherical phases were unchanged in the HAZ relative to the base metal

کلیدواژه‌ها

Mg2Si precipitates over aging 6082-T651 Aluminum alloy Dislocation recovery 6082 T651 Aluminum alloy Welding heat affected zone

نویسندگان

تصویر Mohammad Jula

Mohammad Jula

PhD candidate, Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

تصویر Reza Dehmolaei

Reza Dehmolaei

Assisstant Professor, Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran

تصویر Khalil Ranjbar۳

Khalil Ranjbar۳

Professor, Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran;

شیوه ارجاع

Jula, Mohammad and Dehmolaei, Reza and Ranjbar۳, Khalil,1400,On the Microstructural and Hardness Variations of the Heat Affected Zone in the AA6082-T651 Weld Joints,4th International Conference on Welding and Non Destructive Testing & 22nd National Conference on Welding & Inspection & 11th National Conference on NDT,Isfahan

ارائه‌شده در

پوستر مجموعه مقالات چهارمین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب و بیست و دومین کنفرانس ملی جوش و بازرسی و یازدهمین کنفرانس ملی آزمایش های غیرمخرب مجموعه مقالات چهارمین کنفرانس بین المللی جوشکاری و آزمایش های غیرمخرب و بیست و دومین کنفرانس ملی جوش و بازرسی و یازدهمین کنفرانس ملی آزمایش های غیرمخرب18 اسفند 1400 · اصفهان
ادامه مسیر پژوهش

مقالات مرتبط

مقاله کنفرانسی سال ۱۴۰۰ ۱,۲۸۱ مشاهده

ارزیابی ریسک فرایند جوشکاری و برشکاری با رویکرد FMEA فازی

بدون تردید مدیریت ریسک، مهم ترین ماموریت نظام مدیریت ایمنی در صنایع می باشد ریسک همواره با عدم قطعیت همر…

ارزیابی ریسکفازیجوشکاری
مقاله کنفرانسی سال ۱۴۰۰ ۱,۰۳۶ مشاهده

آزمون های غیر مخرب در صنعت خودروسازی

نظر به اهمیت بالای کیفیت و صحت عملکرد قطعات و اجزاء خودرو در حصول اطمینان از کارایی و ایمنی خودروی تولید…

خودروUTMT
مقاله کنفرانسی سال ۱۴۰۰ ۹۵۵ مشاهده

تکنیک دودیواره دو تصویر برای لوله های با سایز بسیار کم برای ارزیابی مکان عیوب و حساسیت در جوش لب به لب لوله

در این تحقیق لوله های زیر اینچ هیدرولیک ۰/۵ و ۰/۷۵ اینچ با جنس ۱/۰۳۰۸ را در واحد فولادسازی پس از جوشکاری…

لولهآزمون پرتونگاریجوش
مقاله کنفرانسی سال ۱۴۰۰ ۸۰۳ مشاهده

انحلال ذرات کاربید تنگستن (WC) حین ایجاد لایه سخت جوشکاری و تاثیر آن بر مقاومت سایشی لایه کامپوزیتی WC/Ni

در پژوهش حاضر تاثیر انحلال ذرات کاربید تنگستن WC ناشی از شرایط مختلف پیش گرم نمودن قطعات قبل از جوشکاری…

ذرات پودری WCانحلال ذرات کاربید تنگستنتشکیل فاز ترد C۲W
مقاله کنفرانسی سال ۱۴۰۰ ۷۹۳ مشاهده

جوشکاری نقطه ای مقاومتی فولادهای پیشرفته در خودرو سازی

امروزه فراین د جوشکاری مقاومتی نقطه ای یکی از مهم ترین مراحل ساخت خودروها بشمار می رود افزایش ایمنی و سب…

ایمنیسبکیسوخت
مقاله کنفرانسی سال ۱۴۰۰ ۷۶۶ مشاهده

بررسی اثر زمان و دمای پیشگرم روی خواص مکانیکی منطقه متاثر از حرارت جوشکاری به روش GMAW/GTAW ، اتصال آلیاژ ۱.۷۲۲۵ (M۰۴۰) به St۳۷

اتصال فلزات غیرهمجنس یکی از مهم ترین الزامات صنایع مختلف است اتصال فولادهای آلیاژی و ساده کربنی به طور م…

مدت زمان پیشگرمدما پیشگرماتصال فلزات غیر همجنس