درباره کنفرانس
اولین کنفرانس بین المللی و هفتمین کنفرانس ملی مهندسی ساخت و تولید در تاریخ 1 فروردین 1384 توسط دانشگاه تربيت مدرس در شهر تهران استان تهران برگزار می شود.
محورها و حوزه‌های علمی
برگزارکنندگان
- دانشگاه تربيت مدرس
نویسندگان حاضر در این دوره
صادق رحمتی
جواد اکبری
عباس وفایی صفت
مهران کدخدایان
محمد رضا موحدی
جلیل رضایی پژند
محمد زادشکویان
حسین گلستانیان
ابوالفضل خلخالی
کریم زنگنه مدار
مهران محبوب خواه
غلام حسین لیاقت
محمدجواد ناطق
عبدالرضا سیم چی
سیامک اسماعیل زاده خادم
Hasan Moslemi Naeini
حمیدرضا رضایی آشتیانی
حامد دیلمی عضدی
جمال زمانی
فرهنگ عباسی
کریم شلش نژاد
محمود موسوی مشهدی
محمود پاکشیر
خلیل فرهنگ دوست
مقالات این کنفرانس
Critical Factors for Business Competitiveness in Malaysian Automotive Manufacturing SMEs
This paper is based on a survey conducted on top management of component suppliers to Malaysian automoti…
Cutting Temperature, Tool Wear, Surface Roughness and Dimensional Deviation in Cryogenic Machining
Machining of steel inherently generate high cutting temperature, which not only reduces tool life but al…
Damage mechanics model forfatigue life assessment of the drillpipe
This paper deals with the study of a damage mechanics model for the fatigue life assessment of the drill…
Deep Drawing Process Design and CAPP System for Box Shaped Parts
In this work a rule based computer aided process planning system BOX CAPP for deep drawing of box rectan…
Department of Mechanical and Control Engineering,Tokyo Institute of Technology, Tokyo, Japan
More than twenty five 25 types of high carbon iron alloys are used for production of rolls with consecut…
Design & Manufacturing a Robot Wrist: Performance Analysis
In this article, design and manufacturing of a three degrees of freedom robot wrist with the dimensions…
Design Review of Machine Tools Considering Component errors and Structural Deformations
This paper applies a design tool proposed by the author to a milling machine The tool combines the form…
Design and Manufacturing of a Chemical Machine by Jet Propulsion Mechanism
In this work, a chemical machine has been designed and manufactured in which its motive power is supplie…
Design and Manufacturing of a Pipe Inspection Crawler (PIC)
One of the most important requirements in repairing and maintaining of pipelines is the ability to monit…
Design and NC Machining of Complex Surfaces using CAMSURF
Curves and surfaces are important elements in computer aided geometric design Machining of complex surfa…
Design and Production of an Industrial Robot Prototype
A six degree of freedom robot is designed by using Computer Aided Design methods Where necessary, design…
Design and manufacturing of an ultra sensitive seismic sensor
In this research, a seismic sensor for sensing low frequency less than20 Hz with small amplitude about 1…
Design of Optimized Trajectory for Flexible Robotic Arms
This article presents an improved method with a combination of energy methods and the concepts of differ…
Design of a 2-D Servo Press Transfer System Using Linear Stepper Actuators
In this paper a transfer mechanism for moving parts through successive stations of a transfer die is dis…
Design, Manufacture and Experimental Analysis of 3R Robotic Manipulator
Design and manufacturing of a robotic manipulator with three degrees of freedom has been described in th…
Development of Setup-free Machining Technology of Plate-like Components (Software & Hardware)
Traditionally, workpiece holding fixtures have been designed and fabricated only for mass production whe…
Dimensional and Geometrical Tolerance Analysis of Kinematic Assemblies Dimensional and Geometrical Tolerance Analysis of Kinematic Assemblies
Tolerance analysis of assemblies promotes concurrent engineering by bringing engineering requirements an…
Distributed Supply Chain Model— Case Study: Automobile Manufacture Supply Chain Simulation
The competitive success of an organization relies on the efficiency of the entire supply chain Successfu…
Dynamic Force Model for 3- Axis Ball-End Milling of Sculptured Surfaces
Dynamic force model is used to estimate cutting forces of sculptured surface considering dynamic charact…
Effect of Fiber / Matrix Adhesion and Fiber Rate in the Processing of Thermoplastic Composites
The adhesion of glass fibers embedded in a thermoplastic blend matrix of Polycarbonate /Acrylonitrile Bu…